This is the VoltWatch2 on-board Receiver Battery Monitor for
                   4.8V and 6V NiCd and NiMH receiver packs.
    This mounts on the outside of the airplane, so you can see at a glance
        the status of the receiver battery mounted inside.

FEATURES: 7-LEDs provide instant, accurate battery voltage status of Low, Safe,
            or Max. Only one LED glows at a time
          Small switch to select 4.8V or 6V battery
          Very lightweight, only .15oz (4.3g) unit can mount on the side
           of the fuselage, or under the plane's canopy
          Draws amazingly low current - from 4-34mA depending on the battery
          Plugs into any open receiver channel using a Futaba J connector
          One year warranty

Hobbico VoltWatch2 4.8V/6V Rx Battery Monitor $12.49

Hobbico Air Alert Flight Pack Monitor 
    This is an Air Alert Flight Pack Monitor used as a Low Voltage
             and Lost Aircraft Alarm on Radio Controlled Aircraft.

FEATURES: Emits different sequences of "beeps" to signal potentially risky
            flight pack conditions.
            1. Low Battery Alarm- when flight pack voltage levels are low,
               to identify an impending power failure.
            2. Lost Airplane Finder- as a tracking device, when searching for
               a model that has crashed.
            3. Transmitter Inactivity Signal- if the respective Tx stick hasn't
               been moved for over one minute, warns that either the
               transmitter is not turned ON, or the receiver has not been
               turned OFF, or some other signal problem exists.
          For 4.8V battery pack ONLY
          Easy flush mounting inside or outside the fuselage
          Ultra lightweight, micro-thin case is foam-cushioned for durability
            and to protect components inside.
          Includes a Universal connector for use with most common radio systems
            such as Futaba J, Airtronics Z, Hitec S, JR, Tower Hobbies.
          2-year warranty

INCLUDES: One Air Alert Flight Pack Monitor w/One Male and One Female
            Universal Connector
          One 13/16" square of double-sided tape
          One instruction card

REQUIRES: Plug Air Alert into receiver throttle channel, and throttle servo
            into Air Alert. Turn receiver ON. Air Alert will emit One Beep
            to confirm Power is ON.

Futaba R6008HS 8-Channel 2.4GHz FASST Receiver out of stock 139.99, disc
FEATURES: G3 2048 resolution plus FASST benefits including Dual Antenna
            Diversity and significantly reduced latency for lightning quick
          High speed operation allows digital servos to update more rapidly
             than analog servos (both are compatible with this receiver)
          HS (High Speed) mode improves frame rate on channels 1-6 to only
            7 milliseconds-compared to 14 milliseconds at normal mode
          One year limited warranty

INCLUDES: Futaba R6008HS 2.4GHz FASST 8-Channel Receiver with instruction sheet

REQUIRES: Installing in model and connecting servos

SPECS:    Dimensions: 1.8 x 0.9 x 0.5" (45 x 22 x 13mm)
          Weight: 0.48oz (13.5g)
          Power Requirement: 4.8 or 6.0V battery or regulated output from ESC

COMMENTS: In HS mode, digital servos (including those in the BLS series) must
            be used on channels 1-6. Those channels will also operate gyros and
            brushless ESCs. Channels 7 and 8 continue at normal mode and accept
            any servos.

Futaba R617FS 7-Channel 2.4GHz FASST Receiver INSTOCK 89.99
FEATURES: High sensitivity receiver weighs only .25oz (7g) without case
            yet is a full range system for all aircraft from giant scale to
            park flyer applications-no need to buy separate receiver for
            specific aircraft
          Simple one-touch linking - no plugs to mess with or lose
          Dual Antenna Diversity allows 2.4GHz FASST Futaba transmitter to
            select the best reception between the two receiver antennas with no
            signal loss
          Rubber grommets installed where antennas exit to eliminate stress
            and fraying of the two antenna wires
          One year limited warranty

INCLUDES: Futaba R617FS 2.4GHz FASST 7-Channel Receiver

SPECS:    Size: 1.6 x 1.1 x .35" (40 x 27 x 9mm)
          Power Requirement: 4.8 - 6V
          Current Drain: 80mA (at no signal), 74 mA(w/ signal no servos on 4.8)
          Weight: 0.34oz  (9.8g) with case, 0.25oz  (7g) without case

Futaba R6106HFC 6-Channel 2.4GHz FASST Receiver  $ 57.99, disc
FEATURES: Ideal for carbon fuselage sailplanes, and the 50" wingspan class of
          Extended coaxial antenna can be routed outside a carbon fiber
            fuselage for ideal reception
          Use with any servo in normal mode or digital servos in high speed
          End pin design for easy servo connections
          Easy Link ensures receiver recognizes and responds only to
            transmitter it is linked to
          One year limited warranty through manufacturer


       This is the Tactic TTX650 2.4GHz 6-Channel Computer Transmitter.
    **This is a transmitter only, receiver and servos are not included.**

              This transmitter includes all features needed for
 sport and intermediate level pilots to fly almost any airplane or helicopter.

FEATURES: Use true frequency hopping Secure Link Technology making it
            compatible with all Tactic SLT receivers and Tx-R (transmitter
            ready) aircraft
          Pushbutton programming controls and menus are intuitive and
          Eight preprogrammed mixes and four programmable mixes
          Twenty model memory
          User-assignable switches, one momentary switch, two 3-position
            switches, and four two position switches
          Helicopter programming with adjustable 6-point throttle and pitch
          Digital trims for aileron, elevator, throttle and rudder with slow/
            fast adjustment
          All channel reversing, sub-trim, and travel adjustment
          Dual rates and exponential on aileron, elevator and rudder channels
          Large, easy-to-read graphing LCD screen with adjustable contrast
          Ball bearing gimbals and adjustable stick lengths
          Up/Down and battery timers
          Charge jack for optional NiCd/NiMH packs (not included)
          Low voltage alarm
          Firmware upgrade jack
          Wireless trainer system with selectable channels, compatible with the
            Tactic TTX600 and the TTX404 as the student or trainer radios
          External antenna rotates and folds for easy storage
          Ball bearing gimbals and ergonomic case
          One year limited warranty through Hobby Services beginning at date of

INCLUDES: Tactic TTX650 2.4GHz 6-Channel Transmitter with Manual
          Four AA alkaline batteries

REQUIRES: SLT receiver and servos of modeler's choice

Tactic TTX650 6-Channel 2.4GHz SLT Computer Transmitter, on sale 129.99, disc
Product List
seagull /SIG

Futaba R6108SB 8 Channel 2.4Ghz FASST S.Bus Receiver, out of stock129.99
This is the Futaba R6108SB 8 Channel 2.4Ghz FASST S.Bus Receiver. Stop cable clutter with the innovative S.Bus system. It uses digital serial data communication technology to transmit control signals between your receiver and servos. A single S.Bus cable can carry signals to as many channels as your transmitter can handle. You no longer have to worry about plugging in the wrong servo to the wrong channel, because each servo knows what channel it is dedicated to in advance. 

S.Bus receivers are limited only by the number of channels your transmitter will handle. Don’t have S.Bus servos? No problem. SBD-1 S.Bus Decoder Cables let you use existing analog and digital servos, too. The Futaba S.Bus system is nothing short of revolutionary – and the revolution’s just beginning. 

Eliminates clutter
Easy programming with the SBC-1 Channel Setting Tool, S.Bus receivers or PCLink software
No receiver channel limits (except by those on your transmitter)
Plug in battery packs anywhere you wish
Heavy-duty 20-gauge wire
SBD-1 decoder cables (sold separately) let you use existing analog and digital servos
Prevents mismatched servo-channel connections
S.Bus system accessories make any installation simple
Power Requirement: 4.8V or 6.0V battery or regulated output from ESC*
Dimensions: 1-7/8x1x9/16" (47x25x14mm)
Weight: 0.5 oz (14.0 g)