A convenient way to hold and start your plane!   Aero Mate cradles your plane's tail section while you start the engine, make engine adjustments or break in a new engine.
Aero Mate
Cradle Width:  8"
Cradle Height:   13"
Down Rod Length:   12"

Thunderbolt Glow Plug Standard Long 
Thunderbolt Glow Plug   4-Stroke 

Two Stroke Engines
Back to top of page
Back to the Top
BISSON MUFFLERS
Back to the Top
Back to top of page
-  Made with 600 Denier Nylon that is extremely durable 
    and water resistant
-  The inside of our bags are lined with heavy fleece and 6 
    pockets to hold your props and heli blades up to 32"
-  Between the Nylon and the fleece is a layer of 1/8" 
    closed cell foam to help protect your propellers from 
    dings and dents
-  There is a 1½" webbing padded handle
-  The zippers go around three sides so the Props can be 
    inserted easily. Notice the zipper goes all the way 
    around. We only use quality zippers to ensure long life

Prop Tote
Back to the Top
FEATURES: Single RINGED piston and cylinder sleeve
          Includes the Silent muffler (SUPG1561) with exhaust stack
          Schnuerle porting
          Twin-needle carburettor
          One-piece crankcase
          Two crankshaft ball bearings

INCLUDES: One Assembled GS40 Ringed Engine w/Carb.
          One Muffler, Gasket, Mounting Nuts, Bolts, Brass Pressure 
          Fitting, and Exhaust Stack.
          One Set of Instructions, Parts List, and Decals

REQUIRES: Fuel with 5%-15% Nitromethane and 17% or greater
                   lubricant content 
                   Prop
                   Glow Plug

SuperTigre GS-40 Ringed w/Silent Muffler 

SuperTigre GS-45 ABC w/Muffler 

FEATURES: ABC cylinder and piston (An "A"luminum piston with a "B"rass
          "C"hromed cylinder sleeve)
          Two crankshaft ball bearings
          Schnuerle porting
          A NEW silent muffler
          One-piece crankcase
          A twin-needle throttled carburettor

INCLUDES: One Glow Plug
                   One Silent Muffler with Header
                   One Set Operating Instructions
                   One parts list
                   One Set SuperTigre Decals

REQUIRES:  FUEL: 18% oil content MINIMUM. Asynthetic/castor blend is highly recommended. 10%-15% Nitromethane will work well. Higher levels of of Nitromethane may require adjustment of the compression ratio to prevent detonation.

SPECS:  Bore: 21.5mm (.846")
          Stroke: 17.8mm (.701")
          Weight w/o muffler: 372g (13.05oz)
          Weight with muffler: 541g (19.1oz)
          RPM Range:  3,000-17,000
          Displacement: .39 cu in. (6.46cc)
          Power Output: 1.15 BHP at 15,500 RPM
          Width between centers of mounting holes: 42mm (1.65")
          Length between centers of mounting holes: 19mm (.75")
          Width of crankcase excluding mounting flanges: 34mm 
          (1.34")
          Length from backplate to front of drive washer: 80mm 
          (3.15")
          Height from bottom of crankcase to top of head: 84mm 
          (3.31")
          Crankshaft size: 1/4-28
          Suggested prop size: 9x7, 9x8, 10x5, 10x6, 10x7, 11x4, 
          11x5, breakin: 10x6
SPECS:  Bore: 21.85mm (.860")
          Stroke: 20mm (.787")
          Weight w/o muffler: 377g (13.22oz)
          Weight with muffler: 524g (18.5oz)
          Displacement: .46 cu in (7.5cc)
          Power Output: 1.45 BHP at 16,000 RPM
          RPM Range:  2,500-16,000
          Width between centers of mounting holes: 42mm (1.65")
          Length between centers of mounting holes: 19mm (.75")
          Width of crankcase excluding mounting flanges: 34mm 
          (1.34")
          Length from backplate to front of drive washer: 83mm 
          (3.15")
          Height from bottom of crankcase to top of head: 85mm 
          (3.35")
          Crankshaft Thread Size: 1/4-28
          Suggested Props: 10X6 or 9.5X6
                                     10X7 for break-in
Back to the Top
O.S. .40 FX Non-Ringed w/Muffler 
FEATURES: 
1-piece crankcase
       Twin ball bearing-supported crankshaft
       Schnuerle porting (Schnuerle scavenging)
       Advanced Bi-Metallic Liner. This process uses a double layer of
       plating material, rather than one thicker layer. This helps the
       metal to bond to the cylinder, and is more durable. Also, the
       plating process is more consistent, resulting in a more precise
       fit between piston and sleeve, for better compression, longer life.
       Side exhaust
       New carburetor with remote needle mounted on the backplate of the
       engine (to keep fingers away from the spinning propeller).

INCLUDES: 
One Expansion Style Muffler (#873)
       One Assembled .40 FX Engine w/Carb. and Remote Needle Valve
       One Set of Instructions, Parts List, and Decal
SPECS:    Displacement:  6.47cc (0.395 cu in)
          RPM Range: 2,000 - 17,000
          Bore: 20.5mm (.807")
          Stroke: 19.6mm (.772")
          Horsepower: 1.36 BHP at 16,000 RPM
          Weight: 386g (13.6 oz)    16.84 w/muffler
          Length: 85mm (3.35") Distance from the backplate
          to drive washer
          Width: 35mm (1.38")width of engine neglecting
                     engine mounting flanges
                     44mm (1.73")distance between centers of
                     the mounting holes
          Height: 88mm (3.46")
          Crankshaft Thread Size: 1/4-28
          Recommended Props: Break-In: 11x5
          Scale Aircraft: 10.5x6, 10.5x7, 10.5x8, 11x6, 11x7
          Trainer and Sport: 10x6, 11x6

O.S. .50 SX Ringed w/Muffler
FEATURES: 
Produces up to 10% more horsepower than a .46 size
engine and fits in the same size mounting space.
        One-piece metal remote needle valve can be positioned
vertically or horizontally to adapt to in-cowl or side-
mount applications.
        Crankshaft supported by low drag, high-speed dual ball
bearings.
        Universal fuel inlet nipple is rotatable for easier access.
        Ringed piston construction insures long engine life.

INCLUDES: 
One O.S. Max .50 SX Aerobatic Sport Airplane Engine
with 40B carb.
        One #8 glowplug.
        One #873 muffler with 3mm x 35mm socket head cap
screws.
        One instruction book, decal sheet, and warranty sheet.

REQUIRES:
Glow starter, fuel with 5%-15% Nitromethane and 18%
oil content, 2.5mm ball wrench to tighten muffler screws
(can use GPMR8012).
SPECS:   Displacement: 0.499 cu.in." (8.17cc)
              Bore: 0.866" (22mm)
              Stroke: 0.847" (21.5mm)
              Horsepower: 1.8 @ 17,000 rpm
              Practical RPM Range: 2,000-17,000
             Weight: 13.76oz (390g) without muffler
             Crankshaft size: 1/4-28
             Suggested props: 11x6-10,12x6

MOUNTING DIMENSIONS:
Distance between mounting holes on same side: 0.69" (17.5mm)
        Distance between mounting holes on opposite side: 1.73"
(44mm)
        Height from bottom of crankcase to top of cylinder head:
3.50" (89mm)
        Height from center of crankcase to top of cylinder head:
2.77" (70.5)
        Length from needle valve to end of crankshaft: 4.76" (121mm)
        Width at mounting flanges: 2.04" (52mm)
        Width at crankcase: 1.42" (36mm)
Mosfet Power Panel by Hangar 9 
INSTOCK
Key Features
Solid state design
Use with any 12V battery
Supplies power to starters, fuel pumps, and glow plugs
No current drain when panel isn't in use
Pump may be turned on to fill or empty with power switch
2-year warranty

Great Planes C.G. Machine 
FEATURES: Accurately balances your plane and set the center of
            gravity for maximun flight performance
          Works for any type of planes kits, ARFs, high wings,
            low wings with or without struts regardless of size
            or wingspan up to 40 pounds
          Level vial for accuracy

Top Flite Power Point Balancer 
FEATURES: Precision ground balancing shaft, held between two powerful
            "Ceramic 8" magnets allows shaft to "float" for maximum sensitivity
          Inexpensive and easy to use...essential for every modeler.
          Reduces prop vibration-reducing engine wear and prevents
            structural damage
          Can be used anywhere-on the workbench or at the field
          Constructed of long-lasting, high impact plastic and Nickel steel
          Includes instructions explaining how to correct out-of-balance props,
            and even how to use the balancer to determine wind speed.
          Can also be used to balance boat props, car wheels and tires,
            ducted fans, spinners, nose weights and more!
          Balances up to 24" propellers and any size wheels and tires
Z-Bender Pliers by Hangar9 
Key Features
Makes Z-bends quickly and easily
Heat-treated steel construction
Rubber-coated handles for a firm grip
Perfect for all control linkage needs
2-year warranty

Top Flite Trim Seal Tool 
FEATURES: Great for hard to reach places using specially designed tips for
            fillets, curves, and corners
          High and Low settings let you choose the best temperature for your
            covering material
          2-year warranty

INCLUDES: One Trim Seal Tool w/six foot AC cord (US standard)
          One Rounded Shoe
          One Flat Shoe
          One Aluminum Stand

Great Planes Slot Machine/Accessory Gift Pack
FEATURES: Convenient All-In-One Package Eliminates Guesswork.
          Great for beginners or advanced modelers, having the Slot Machine
            Hinge Slot Cutter, Precision Center Marking Tool, Thick Blades and
            Blades for Nylon Hinges, all to cut hinge slots quickly and
            cleanly into airplane wings.
          High Quality Great Planes Accessories.
          This is the version of the Slot Machine With a cord.

INCLUDES: One Great Planes Slot Machine Hinge Slot Cutter
          One Great Planes Precision Center Marking Tool
          One Great Planes Set of Thick Blades
          One Great Planes Set Medium Blades for Nylon
Top Flite Woodpecker Perforating Tool 
 The Woodpecker is a tool designed to keep air bubbles from forming beneath
film covering (such as MonoKote, Ultracote, etc). It prevent air pockets from
forming between covering and wood or from between two layers of film.
  The tool has four wheels with VERY sharp tines that make small, short slices
in wood and/or covering to release the trapped air that causes bubbles in film
covering. The wheels are removable to make the work area of the tool narrower
(for corners, etc).
  Constructed entirely of stainless steel, the handle is rubber covered for
comfort and grip.

Sealing Iron by Hangar 9 
Key Features
Precise thermostatic control up to 450 degrees
Contoured teflon-coated shoe

Great Planes AccuThrow Deflection Meter 
                            
 The Great Planes Accu-Throw Control Surface Deflection Meter Accurately
Adjusts Control Throws for the Best Flight Performance on R/C Aircraft.  This
Gauge is UNASSEMBLED.

FEATURES: Unique design provides the easiest, most accurate measurements
          Works with most models, from trainers to jets, with control
            surfaces up to 5" wide
          Rubber attachement feet grip securely while protecting the airplane's
            finish
          Curved ruler matches the controls' motion for precise readings
            in standard and metric scales (up to 2" or 51mm)
          Perfect for setting up dual rates

INCLUDES: Ruler (with metric scale on one side and standard on the other)
          Two long and two short support wires (for use on large and small
            surfaces)
          All necessary hardware with hex wrench for assembly
          Illustrated instructions

SIG's Wood Floats RTF 
Pre-built and ready to use, the SIG Wood Floats RTF will quickly convert your landlocked model aircraft for water use. The floats include twin water rudders, hardware and everything needed for mounting and control. The .40 Class Floats use a clever but effective connection to drive the water rudders from the aircraft's rudder while the 1.20 class floats use a pull-pull water rudder system. 
 

Built from lite-ply and balsa and pre-covered in SIG AeroKote® using a proven watertight seam overlap technique, the floats are light, strong and perform beautifully. The .40 Class Floats are ideal for aircraft up to 7 lbs (3175 g) while the 1.20 Class Floats are for larger aircraft up to 16 lbs (7257 g). Rascal 110 shown but not included.
OUT OF STOCK $99.99 
ROTOFLOW FUEL TANKS INSTOCK
Go With the Flow!
Feel the difference of the RotoFlow’s revolutionary clunkless fuel delivery and end the worries of what is going on inside your tank when your plane leaves the ground.

It's About Time 
Fuel tanks for RC airplanes have not evolved for decades. They are still prone to the same problems fought during every flying season:

-Clunks stick in forward position 
-Leaking internal and external connections 
-Stiffening of the clunk hose 
-Hoses falling off sharp-ended copper tubes 
-Stoppers degrading and leaking fuel into the interior of the airplane 
-Worst of all - air bubbles in the fuel lines caused by clunk agitation as it impacts the inner tank wall

The new RotoFlow clunkless fuel tank has solved these problems and added a host of new benefits.RotoFlow - A Better Way To Go
-Brass rotary fuel pick-up works on the principle of centrifugal force to ensure constant and reliable contact with fuel
-Fuel is drawn away from the foam layer at the wall of the tank
-No internal hoses or connections to harden, or leak air or fuel
-A harder-hitting throttle response due to the ability to draw from a more foamless and air bubble-free fuel supply
-Works with gas or glow fuels
-Zero maintenance
-Triple-sealed, machined stopper will not leak or take a set
-Barbed brass outlet nipple secures both 1/8" and 5/32" fuel hoses
-Aerospace seals for performance and durability
-No assembly
-One year warranty
Phoenix R/C Pro Simulator V5.0 by RUNTIME GAMES LTD instock


Improved airplane physics rebuilt from the ground up, plus industry-leading heli physics, provide ultimate realism and accuracy
Companion software lets you import 3D geometry definitions from almost any program so that you can fly creations of your own, then share online
Improved model editing system lets you completely control each models flight characteristics in detail
The most authentic simulations of Horizon Hobby® RC aircraft including the innovations they feature such as AS3X® and SAFE™ technology
All aircraft flying sites and feature downloads are FREE
Over 200 accurately modeled and detailed helis, airplanes, float planes, autogyros and more included
In-cockpit and chase camera views give you a wide range of flight perspectives
Realistic sounds recorded from actual model engines
Dozens of beautiful sites include a range of exotic locations from around the world using high-definition Photofield technology that make it feel like you’re right there
Internet/LAN multiplayer mode with voice-chat lets you fly and learn from other pilots around the world
Tutorial videos taught by world-class champion pilots
Overview

Whenever weather, schedules or circumstances conspire to keep you from the flying field, scratch your flying itch with the latest Phoenix Professional RC Flight Simulator, version 5.0. Stunning graphics and incredibly realistic physics have made the Phoenix simulator not only one of the best desktop flight simulators, but a virtual RC experience with just about all the benefits of an RC club and flying field. This newest version features definitively refined physics plus new companion software you can use to create your own models, fly them and then share them online. It’s always a perfect time to fly with the Phoenix Professional RC Flight Simulator. 

Phoenix is the incredibly popular worldwide RC simulator that lets you master this complex and rewarding hobby in the comfort of your own home. Whether you are a brand new pilot picking up your first trainer model, or a seasoned veteran practicing for your next big competition, Phoenix has everything you need to take your skills to the next level. Blending incredibly life-like and accurate model physics with beautiful cutting-edge graphics and a multitude of unique features, Phoenix is a fantastic package for beginners and professional model pilots alike. 

CREATE YOUR OWN MODELS 
Included software lets you import 3D geometry definitions from almost any 3D design program to fly them, then share online. 

EASY MODEL EDITING 
The improved model editing system lets you completely control each models flight characteristics in detail with ease. 

ALL MODELS AND SITES ARE FREE 
Hundreds of models and a wide range of flying sites are included with free downloads available as additional scenery and aircraft are available. No expansion packs required. 

AUTHENTIC AIRCRAFT AND TECHNOLOGY 
Phoenix 5 is the only RC sim with authentic Horizon Hobby aircraft simulations including the innovations they feature such as AS3X® and SAFE™ technology. 

FLY FOREVER! 
Whether you’re learning to fly without harsh consequences or just trying out that Blade heli you have had your eye on, the InfinityScape 3D landscape generator lets you fly beyond the horizon over beautiful, ever-changing terrain that you create and control. 

System Requirements

IBM-compatible PC computer with 1.0 GHz Pentium 3/4 or AMD Athlon/64 compatible processor or better 
Microsoft Windows XP, Windows 7 or Windows 8 operating system 
256MB system memory (RAM) 
1.5 GB free, uncompressed hard-disk space 
ATI Radeon 9800/NVidia Geforce Ti4200 with at least 128MB memory or better 
Microsoft DirectX 9.0c or higher 
DVD-ROM Drive for installation 
1 free USB 1.1/2.0 port 
100% DirectX 9 compatible sound card (optional) 
Other specifications may apply
GPMQ1882.40 Size Float Set Preassembled

  This is the Great Planes almost ready to fly .40 size Float Set.  
   
FEATURES: Lightweight fiberglass construction, already finished can be used  
  right out of box or painted if desired  
  Fits .40-.60 size R/C aircraft weighing between 5-9.5 lb (2270-4310g)
  Fast, easy final assembly right at lake or pond with included  
  installation hardware  
  High performance design raises aircraft off the water smoothly and  
  safely, ventral fin preserves low speed flight stability and  
  straight tracking  
  Water rudder can be steered with a servo (not included) or directly  
  from the airplane rudder using the included nylon pushrods  
  Warranty: Great Planes Model Manufacturing guarantees this Float Set 
  to be free from defects in both material and workmanship at the  
  date of purchase. This warranty does not cover any component parts
  damaged by use or modification.  
   
INCLUDES: Left and right floats, float gear wire, servo mount, ventral fin,  
  two pushrods, water rudder, hardware package, and photo-illustrated
  instruction manual  
   
REQUIRES: Adhesives and building supplies  
  Standard servo, 12" (300mm) servo extension, Y-harness if using  
  in-float servo option  
   
SPECS: Float Length: 38.5" (978mm)  
  Model Weight Class: 5.0-9.5lbs (2270-4310g)  
  Model Size Class: .40-.60  
  Approximate Weight of Assembled Floats: 3.14lbs (1424g)  
   
COMMENTS: The box says they are 34.5" long but they are really 38.5"  
   
HCAP3305Panel Ready TorqMaster 180 CE

  This is a Hobbico TorqMaster 180 Deluxe 12V Starter.  
It is designed for starting Glow or Gas Engines up to 1.8 cubic inches in size.
   
  *** 2-Year Warranty ***  
   
FEATURES: An Aluminum Starter Cone with V-Groove for Boat Starter Belts and  
  Round Rubber Insert for Airplane Spinner Cones  
  Starter has Self-Adjusting Carbon Brushes for Longer Lasting Useage  
  and Constant Contact with the Armature  
  Easy-Press Start Switch makes Starting Easy Without Requiring Heavy  
  Finger Pressure and a built-in Finger-Guard promises Safe Starts  
   
INCLUDES: One TorqMaster 180 Deluxe 12V Starter w/5' Cord & Banana Plugs  
   
REQUIRES: A 12V DC power source such as HCAP0800 or HCAP0901  
   
SPECS: Shaft thread size- 6x1.0mm  
   
HCAP3200TorqMaster 90 Deluxe 12V

  This is a Hobbico TorqMaster 90 Deluxe 12V Starter.  
  It is designed for starting Glow Engines up to .90 cubic inches in size.  
   
  *** 2-Year Warranty ***  
   
FEATURES: An Aluminum Starter Cone with V-Groove for Boat Starter Belts and  
  Round Rubber Insert for Airplane Spinner Cones.  
  Starter has Self-Adjusting Carbon Brushes for Longer Lasting Useage  
  and Constant Contact with the Armature.  
  Easy-Press Start Switch makes Starting Easy Without Requiring Heavy  
  Finger Pressure and a built-in Finger-Guard promises Safe Starts.  
  Pre-Attached Alligator Clips for easy attachment to a 12V battery  
   
INCLUDES: One TorqMaster 90 Deluxe 12V Starter w/5' Cord & Alligator Clips.  
   
SPECS: Winding Resistance: 1.3 ohms Brush width: 3/16"  
  Weight: 3lbs and 6oz Current Draw: 11.6A load  
  Armature length: 2" RPM: no load 4500rpm, load 3100rpm  
  # of commutator contacts: 10 or 12 Measured torque: 310 oz-in at stall  
  Shaft thread size- 6mm-1.0mm  
The O.S. #8 glow plug is the most widely used O.S. glow plug.  
 Recommended for most current O.S. (and other brands of) 2-stroke R/C engines. 
   
FEATURES: Medium heat range plug for most model engine applications.  
  Plug is medium length, without idle bar. For all 2 stroke engines.  
   
INCLUDES: One glow plug and one brass washer  
   
SPECS: Threads on the plug are 1/4-32.