AX90032 Yeti XL 4WD RTR
IN STOCK, 699.99
Axial Wraith Jeep Wrangler Poison Spyder Rock Racer RTR AX90031 INSTOCK 399.99
FEATURES: Chassis: Full tube composite chassis
          Drive: Four wheel with locked differentials and offset pumpkin for
            more ground clearance and a better driveshaft angle, AR60 OCP-Axle
            constructed from high strength, low flex composite material, axle
            tubes are reinforced and beefed up with a boxed-in axle truss to
            distribute stress over a larger area
          Radio: AX-3 2.4GHz 2-channel with steering and throttle trim and
            reverse
          ESC: AE-2 with LiPo cutoff, drag brake, Tamiya connector, and is
            programmable with the Castle Link programmer (not included)
          Motor: 20 turn
          Body: Officially licensed Jeep Wrangler body with Poison Spyder
            graphics
          Battery Tray: Sized for standard stick pack and LiPo packs up to
            1.8x5.9x1.1" (47x150x28mm) in size
          Suspension: True four link
          Shocks: Composite body
          Wheels: Officially licensed Trail Ready HD series beadlock, wheels
            mount to any Axial Wraith, AX10 Ridgecrest or SCX10
          Tires: BFGoodrich Krawler T/A KX


INCLUDES: RTR Jeep Wrangler Wraith-Poison Spyder with 2.4GHz Radio, Motor, ESC,
            and Instructions


REQUIRES:


SPECS:    Wheelbase: 13.98" (355mm)
          Ground Clearance: 2.8" (71.6mm)
          Height: 9.1" (232mm)
          Width: 11.22" (285mm)
          Length: 19.25" (489mm)
          Weight: 5.45lbs (2.47kg)


AX90026 1/10 Yeti 4WD RTR ON ORDER 429.99
 This is the 1/10 scale Ready to Run Electric Powered, Radio Controlled  
  Yeti Rock Racer from Axial.  
   
  **NOTE Please read the Yeti Pre-run checklist before running your Yeti**  
  http://www.axialracing.com/blog_posts/1073909593  
   
FEATURES: Chassis: Plastic tub type with bolt-on 4 link mount for rear  
  suspension,  
  Drive: Four wheel, WB8 HD rear driveshaft  
  Motor: Brushless, 3150kV, 4-pole  
  ESC: Castle Creations Vanguard, waterproof, 3S LiPo compatible, can  
  be programmed manually via the the Castle Link Programming Card  
  (not included, order CSEM6300) or the Castle Link software  
  interface (not included)  
  Radio: Axial 2-channel AX-3 2.4GHz w/reverse & trim settings, with  
  TSX45 151 oz-in metal gear, dual ball bearing steering servo  
  lightweight 3-channel receiver  
  Shocks: Aluminum body, oil filled  
  Steering: Updated dual shear rack  
  Transmission: Single speed with brushless motor gearing (2nd gear  
  fixed), adjustable motor mount, 2-speed optional gear set will be  
  available in the future  
  Slipper Clutch: Dual design uses a pad on each side of spur gear for 
  added surface area for more precise tuning and holding power  
  Front Suspension: Independent design allows better control direction 
  of travel ant high speeds when one side is adjusting to road  
  obstructions  
  Rear Suspension: AR60 rear solid axle, multiple tuning options, sway 
  bar, EXO suspension arms, anti squat adjustments built into four  
  link mounts at chassis, lower links designed to hold optional dual 
  shocks  
  Front Bumper: New KOH style with light mounts, and compression mount 
  Wheels: Officially licensed Walker Evans 3-piece beadlock design,  
  black in color, adjustable breather holes, compatible with most  
  2.2" tires, width: 1.7" (44.6mm), diameter 2.6" (65.5mm)  
  Tires: BF Goodrich Crawler T/A KX, width: 1.8" (47mm), inner  
  diameter: 2.2" (56mm), outer diameter: 5.1" (130mm)  
  Body: Molded lexan, one-piece with separate roof, scale accessories  
  spare tire mount, scale interior with driver and passenger helmet  
  rear cage captures upper shock mounting points and includes  
  integrated scale fuel cell  
  Battery Tray: Fully adjustable and easily accessible  
   
INCLUDES: RTR Yeti Rock Racer with 2.4GHz Radio, ESC, Brushless Motor, Body,  
  Body Accessories, 32P 64P Spur Gear, 32P 16T Pinion Gear,  
  Instruction Manual  
   
REQUIRES: Battery: 2S or 3S LiPo pack with Dean's connector  
  Battery Charger: To match selected LiPo Battery  
  LiPo Charging Sack, Track and Maintenance Eequipment  
   
SPECS: Vehicle,  
  Length: 19.5" (495mm)  
  Width: 12.3" (312mm)  
  Height: 7.7" (195mm)  
  Wheelbase: 14.25" (360mm)  
  Ground Clearance: 2" (50mm)  
  Weight: 6.51lbs (2.9kg)  
  Body,  
  Length: 17.2" (437mm)  
  Width: 7.3" (185mm)  
  Height: 5.5" (140mm) including roof  
   
  This is the Electric Powered, 2.4GHz Radio Controlled, 1/8 scale  
  Ready to Run Yeti XL Monster Buggy.  
   
FEATURES: Chassis: Composite plastic with integrated upper and lower aluminum  
  braces for greater stiffness, multiple upper link positions to  
  adjust anti-squat  
  Drive: Four wheel shaft, AR60XL solid rear axle, WB XL CVJ rear  
  driveshaft with captured cross pin design-no set screws to lose  
  Brushless Motor: Castle Creations 2200kV, 4-pole  
  Receiver Box: Waterproof, integrated into bottom of chassis  
  Battery Trays: Two, easily accessible from sides of chassis  
  Radio: 2-channel AX-3 2.4GHz pistol grip with trims dials and servo  
  reverse switches, 3-channel receiver  
  Steering Servo: Tactic TSX45 metal gear, high-torque, water resistant
  Electronic Speed Control: Vanguard AE-4 XL 6S/4S LiPo compatible  
  can be programmed manually via Castle Field Programming Card or the
  or through the Castle Link software interface (optional)  
  Shocks: Oil-filled 16mm Big Bore, 20mm aluminum bodies, 4mm shafts  
  Transmission: All metal gears, single speed, full ball bearing  
  equipped, optional two-speed transmission component sold separately
  Differentials: CNC cut metal gears  
  Steering: Dual shear rack  
  Suspension: Front, independent, rear 4-link  
  Wheels: Officially licensed Raceline Monster wheels, 3.8" (96mm)  
  diameter  
  Tires: BF Goodrich Krawler T/A KX 2.9 x 7.25" (74 x 184mm)  
  Body: Trimmed and painted, polycarbonate interior tray with molded  
  driver and passenger figures, dashboard and center console detail  
   
INCLUDES: RTR Yeti XL Monster Buggy with Radio System, ESC, Motor, Body,  
  4-Way Wrench and Instruction Manual  
   
REQUIRES: Batteries: Two 2S or 3S LiPo Packs with Dean's Ultra connector, 25C  
  minimum discharge rating  
  Battery Charger: To match selected batteries  
  AA Batteries: Four for transmitter  
  LiPo charge bag, maintenance and trail equipment  
   
SPECS: Vehicle;  
  Length: 25.75" (654mm)  
  Width: 16.3" (414mm)  
  Height: 11.10" (282mm)  
  Wheelbase: 18.5" (470mm)  
  Ground Clearance: 2.48" (63mm)  
  Weight: 12.75" (5.78kg)  
  Body;  
  Length: 23.5" (597mm)  
  Width: 9.7" (247mm)  
  Height: 6.8" (173mm)  
  Thickness: .040" (1.02mm)  
  Battery Tray Dimensions;  
  Length: 6.89in(175mm)  
  Height: 1.3in (33mm)  
  Width: 1.7in (43mm)  
AX90057 INSTOCK 329.99
SMT10™ MAX-D Monster Jam Truck 1/10th Scale Electric 4WD - RTR
Over the past decade, Axial has been synonymous with crawlers and the scale trail community for creating vehicles that inspires endless adventure and creative freedom. Something interesting started to evolve and a trend began to appear, 4WD straight axle Monster Jam® Trucks. What better to build upon that trend than to offer one of the most striking trucks within Monster Jam®, MAX-D™. Since 2003, MAX-D™ has won 11 Monster Jam World Finals® championships and brought crowds to their feet with daredevil maneuver
AX90055 INSTOCK 329.99
SMT10™ Grave Digger Monster Jam Truck 1/10th Scale Electric 4WD – RTR
Over the past decade, Axial has been synonymous with crawlers and the scale trail community for creating vehicles that inspire endless adventure and creative freedom. Something interesting started to evolve and a trend began to appear, 4WD straight axle Monster Jam® Trucks. What’s usually the first thought that comes to mind when someone mentions Monster Jam? Grave Digger® – who is sitting right up on top! The iconic black, purple, and green graveyard themed paint job has been haunting and thrilling fans for over 30 years...
AX90046 1/10 SCX10 II Jeep Cherokee 4WD Kit​ 
instock 349.99
  This is the Electric Powered, Radio Controlled, 1/10 scale  
  SCX10 II 2000 Jeep Cherokee 4WD All Terrain Kit from Axial.  

FEATURES: Chassis: Scale steel C-channel side rails with adjustable body mount,
  adjustable bumper mounts with swaybar mounting points, mounting  
  points for optional 2-speed and servo winch, adjustable chassis  
  mounted servo system  
  Drive: Full time 4WD locked drivetrain with WB8 HD Wild Boar  
  driveshafts, UVJ style front driveshafts for increased steering  
  angle, full ball bearing drivetrain  
  Transmission: Two-speed capable, all metal gear with transfer case  
  design that allows optimal position for drive shafts  
  Slipper Clutch: Dual pad design for added surface area  
  Spur Gear: 56T 32-pitch  
  Pinion Gear 15T 32-pitch  
  Battery Tray: Easy access front mount, accomodates batteries up to  
  1.2 x 1.7 x 5.8" (32x44x147mm) 3S, 5000mAh  
  Front and Rear Axles: Hardened steel  
  AR44 Hi-Pinion Axle: Hypoid cut CNC metal gears, optimized gear  
  ratio for reduced torque twist, optional gearing choices, one-  
  piece axle housing, increased clearance, larger load rated  
  bearings for durability, 8° kingpin axle eliminates tire scrub,  
  single piece axle housing, one-piece all metal locker, 10°  
  increment adjustments for knuckle carriers and straight axle  
  adapters, optimized gear ratio; 3.75 compared to 2.92 previously,  
  for less torque twist  
  Body: Clear Jeep Cherokee with JCR Classic Rock Sliders, Pre-runner  
  Roof Rack, and Vanguard Bumpers  
  Wheels: 1.9" Method, composite plastic construction, black in color  
  Tires: BF Goodrich A/T KO2, sticky R35 compound, 4.65" (118mm)  
  outer diameter, 1.7" (42.5mm) wide  
  Shocks: Icon polished, 7mm diameter shafts, aluminum body,  
  rebuildable  
  Suspension: Optimized suspension geometry with integrated mounts  
  upper and lower aluminum links, 4-link design reduces axle steer  
  and torque twist, and guards against suspension wrap-up in high-  
  power applications  
  Steering: Proper CMS geometry using 3-link setup with panhard bar,  
  45° steering angle  
  Warranty: Axial warrants this kit to be free from defects in  
  materials and workmanship when new. This warranty does not cover  
  damages due to normal wear and tear, user's failure to perform  
  routine mantenance, user error of assembly or installation, user  
  modifications, addition of aftermarket parts or option parts.  

INCLUDES: SCX10 II Jeep 4WD All Terrain Kit, Shocks, Wheels, Tires, clear  
  Body, Rock Sliders, Pre-runner Roof Rack and Vanguard Bumpers,  
  Decals, Waterproof Receiver Box, and Instruction Manual  

REQUIRES: Motor: 540 size 4-pole brushless recommended  
  Electronic Speed Control: To match selected motor  
  Radio: 2-channel with high torque steering servo  
  Battery: 6-cell NiMH or 2-3S LiPo  
  Battery Charger: Compatible with selected battery  
  Building and track equipment  

SPECS: Vehicle-  
  Length: 22.1" (561.9mm)  
  Width: 8.9" (228mm)  
  Height: 10.5" (268mm)  
  Wheelbase: 12.3" (312.4mm) adjustable with optional link kits sold  
  separately  
  Ground Clearance: 3.0" (77mm)  
  Weight: 4.5lbs (2.04kg) approximately, with electronics  
  Final Drive Ratio (FDR): 40.44, stock  
  (33.69-54.15 with different spur/pinion gear combinations, extra  
  spur and pinion gears must be purchased separately)  
  Body-  
  Length: 20.1" (511mm)  
  Width: 8.3" (211mm) behind front wheels, narrowest point  
  9.0" (230mm) at rear wheels, widest point  
  Height: 5.4" (137mm)  
.AX90054 Yeti 1/18TH Electric 4WD RTR​, OUT OF STOCK
.FEATURES: Chassis: Molded plastic  
  Drive: Four wheel shaft  
  Rear Axle: AR18 solid rear axle, two-piece design, captured pinion  
  gear, three link rear suspension  
  Radio: Tactic TTX200 SLT 2-channel pistol grip, steering and  
  throttle trim and reverse, and end point adjustment  
  Steering Servo: Tactic TSX106 water resistant metal gear with  
  26.5oz/in of torque  
  Electronic Speed Control: Tactic RE20 2.4GHz receiver/ESC combo  
  auto-bind with LED indicator, 2S LiPo capable with voltage cut-off,
  and adjustable drag brake  
  Motor: 380 size 40 turn brush equipped  
  Pinion Gear: 48P 15T metal  
  Suspension: IFS (independent front suspension), floating solid 8mm  
  rear axle with 12mm hex adapter and open diff  
  Shocks: Oil-filled, 3mm shafts  
  Battery: Duratrax Onyx 7.2V 1300mAh NiMH with mini connector  
  Battery Charger: Duratrax Onyx USB NiMH  
  Battery Tray: Length and height adjustable, accomodates 6-cell NiMH  
  or 2S LiPos  
  Motor Mount: Adjustable  
  Wheels: Method Race beadlock style, black in color, 12mm hex  
  Tires: BF Goodrich Krawler  
  Ball Bearings: Full set of sealed ball bearings included  
  Warranty: Axial warrants this kit to be free from defects in  
  materials and workmanship when new. This warranty does not cover  
  damages due to normal wear and tear, user's failure to perform  
  routine mantenance, user error of assembly or installation, user  
  modifications, addition of aftermarket parts or option parts.  
  Ten day limited warranty from date of purchase on electronics.  

INCLUDES: RTR Yeti Jr Rock Racer with Motor, Radio System, Battery,  
  Charger, Painted Body, four AA Batteries and Instruction Manual  

SPECS: Length: 11.6" (295mm)  
  Width: 6.9" (175mm)  
  Height: 5.0" (128mm)  
  Wheelbase: 8.1" (206mm)  
  Ground Clearance: 1.1" (27mm)  
  Weight: 1.75lbs (0.80kg) RTR with included battery  
AX90045 1/10 Wraith Spawn 4WD RTR INSTOCK 369.99

TECH NOTES

  This is the Radio Controlled, Electric Powered, Ready to Run  
  Wraith Spawn Rock Racer from Axial Racing.  

FEATURES: Chassis: Full tube composite chassis  
  Drive: Four wheel with locked differentials and offset pumpkin for  
  more ground clearance and a better driveshaft angle, AR60 OCP-Axle 
  constructed from high strength, low flex composite material, axle  
  tubes are reinforced and beefed up with a boxed-in axle truss to  
  distribute stress over a larger area  
  Radio: 2-channel pistol grip with steering and throttle  
  trim and reverse  
  Steering Servo: Tactic TSX45 metal gear servo with 151 oz-in of  
  torque, metal gear train and dual ball bearings  
  ESC: AE-5, waterproof-can be switched between LiPo and NiMH battery  
  types with a simple jumper, 3S LiPo compatible, drag brake  
  Motor: 20 turn brushed  
  Slipper Clutch: Dual pad for added surface area, 32P spur gear  
  for high-torque applications  
  Body: Retro styled SUV body with realistic driver figure complete  
  with race suit and three interchangeable helmets, motocross,  
  open skull face or motorsport version, body is also compatible  
  with Wraith, AX10 and SCX10 chassis  
  Battery Tray: Sized for standard stick pack and LiPo packs up to  
  1.8x5.9x1.1" (47x150x28mm) in size  
  Receiver Box: Waterproof, silicone seals for antenna, servo wires and
  receiver box lid  
  Suspension: True four link optimized to reduce axle steer, and to  
  have the proper amount of anti-squat and roll characteristics  
  Shocks: Composite body , oil filled  
  Wheels: Method IFD (interchangeble face design) beadlock design,  
  black in color, adjustable breather holes for fine tuning tire  
  performance  
  Tires: Ripsaw 2.2  
AX90048 1/10 RR10 4WD RTR ON ORDER 399.99

  This is the Radio Controlled, Electric Powered 1/10 scale  
  Ready to Run Off-Road 4WD RR10 Bomber Rock Racer from Axial Racing.  
   
FEATURES: Chassis: Licensed Bomber Fabrication scale tube, high-strength  
  composite plastic  
  Drive: Four wheel shaft  
  Front and Rear Driveshafts: WB8 HD Wildboar, updated design with  
  larger diameter cross pin with a 2mm hex drive for added strength, 
  center splined slider floater tube with added material that  
  reduces flex and fatigue, captured cross pin design offers greater 
  durability and easier maintenance than set screw design  
  AR60 OCP Axle: High-strength composite material, tubes reinforced  
  with boxed-in axle truss, off-center pumpkin, updated steering  
  knuckles for dual shear & elimination of secondary bolt on plate,  
  updated diff cover and servo mount for new look  
  Transmission: RR10 specific all metal internal gears, full ball  
  bearings, single speed w/high gear for higher speed, two-speed  
  component sold separately  
  Slipper Clutch: Dual slipper design, 32P 56T spur gear for high-  
  torque applications  
  Motor Mount: Integrated with transmission, wide range of movement  
  for endless gearing options  
  Motor: Axial AX31312 35 turn brushed  
  Electronic Speed Control: AE-5 3S LiPo compatible, switchable on the 
  track between NiMH and LiPo batteries with a simple jumper-no  
  complex procedures  
  Radio: Tactic 2.4GHz SLT 3-ch TTX300, programmable 3rd channel  
  operates two-speed shifting, winches and lights (not included),  
  TR325 2-ch receiver  
  Steering Servo: Tactic TSX45, metal gear, water resistant, dual ball 
  bearings, 151 oz-in torque  
  Shocks: Clear coated polished aluminum body King shocks, precision  
  machined pistons for smooth performance throughout range of travel,
  super soft blue springs, optional front & rear secondary shock  
  mounts, dual shear shock mounting locations  
  Suspension: 4-link, rear swaybar mounts for optional rear  
  swaybar (AXIC3331)  
  Wheels: 2.2" Walker Evans Racing, black in color, 12mm hex  
  Tires: BF Goodrich Baja T/A KR2, S30 sport compound  
  Steering: Direct, updated knuckles for dual shear, eliminates  
  secondary bolt-on plate  
  Interior: Polycarbonate tray w/driver figures and dashboard, three  
  pairs of black styrene helmets (motorsport, open skull face &  
  motorcross), scale molded shock reservoirs  
  Battery Tray: Forward mount easy access  
   
INCLUDES: RTR Axial RR10 Bomber with Motor, ESC, 3-Channel Radio, Tires, Wheels
  Interior Detail and Instruction Manual  
   
REQUIRES: Battery: 2-3S LiPo  
  Battery Charger: Compatible with selected battery  
  AA Batteries: Four for transmitter  
  Track and maintenance equipment  
   
   
SPECS: Overall Width (Face to Face): 11" (280mm)  
  Length: 22.4: (570mm)  
  Height: 9" (230mm)  
  Wheelbase: 14.75" (375mm)  
  Ground Clearance: 2.8" (72mm)  
  Weight: 6.25lbs (2.83kg)  
   
  Battery tray:  
  Width: 6" (152mm)  
  Height: 2" (51mm)  
  Length: 1 1/8"-1 5/8" (29mm-42mm)  
   
AX24206 2CH 2.4Ghz Radio System AX-3/AR-3
INSTOCK 69.99 

TECH NOTES

This is the Axial 2.4GHz 2-Channel Radio System with Transmitter and Receiver. 
  Servos Not Included.  
   
FEATURES: Used in Axial RTR vehicles  
  Steering and throttle trim  
  Steering dual rate  
  One touch linking  
   
INCLUDES: AX-3 Transmitter  
  AR-3 Receiver  
  Instruction Sheet  
   
REQUIRES: AA Cells: Eight for transmitter  
  Servos of modeler's choice  
   
SPECS: Transmitter-  
  Operating Voltage: 12V  
  Output Power: 80mW  
  Size: 12.2 x 5.9 x 2.9" (310 x 150 x 75mm)  
  Receiver-  
  Size: 1.5 x 094 x 0.59" (39 x 24 x 15mm)  
  Weight: 0.46oz (13.2g)  
  Channels: Two  
.AX90050 1/10 Yeti Trophy Truck Electric RTR 449.99 ON ORDER
​ This is the 1/10 scale Ready to Run Electric Powered, Radio Controlled  
  Yeti SCORE Trophy Truck from Axial Racing.  
   
  The Yeti Trophy SCORE Truck differs from the previous Yeti versions  
  in the following ways;  
   
  The TT has greater rearward weight bias with  
  different spring rates and shock oil tuned for  
  balance and high-speed desert racing  
   
  Longer Trailing Arm Independent Rear Suspension  
  for better handling and more travel  
   
  Rear Cage and molded details specific to Yeti TT body  
   
FEATURES: Chassis: Plastic tub type with bolt-on 4 link mount for rear  
  suspension,  
  Drive: Four wheel, WB8 HD rear driveshaft  
  Motor: Brushless, 3150kV, 4-pole, water resistant  
  ESC: Vanguard, waterproof, 3S LiPo compatible, can be programmed  
  manually via the the Castle Link Programming Card  
  (not included, order CSEM6300) or the Castle Link software  
  interface (not included)  
  Radio: Tactic TTX300 2.4GHz w/reverse & trim settings, with  
  TSX45 151 oz-in metal gear, dual ball bearing steering servo  
  lightweight 3-channel receiver  
  Shocks: Polished aluminum body King shocks, oil filled  
  Steering: Dual sheer rack  
  Transmission: Single speed with brushless motor gearing (2nd gear  
  fixed), adjustable motor mount, 2-speed optional gear set  
  available by ordering AXIC0999  
  Slipper Clutch: Dual design uses a pad on each side of spur gear for 
  added surface area for more precise tuning and holding power  
  Front Suspension: Independent design allows better control direction 
  of travel ant high speeds when one side is adjusting to road  
  obstructions  
  Rear Suspension: AR60 rear solid axle, multiple tuning options, sway 
  bar, EXO suspension arms, anti squat adjustments built into four  
  link mounts at chassis, lower links designed to hold optional dual 
  shocks  
  Wheels: Officially licensed Method 105 wheels black in color,  
  compatible with 2.2/3.0 short course tires  
  Tires: BF Goodrich Baja T/A KR2 Tires: 3.0" (79mm), inner  
  diameter: 2.2" (56mm)  
  Body: Molded lexan one-piece, realistic scale accessories  
  interior tray with molded driver figures and dashboard, three  
  pairs of black styrene helments (Sparco, Moto-X, Skullu), exhaust  
  outlets on top of rear fender, molded & hood vents and plastic  
  light buckets at all 4 corners. Simply add our LED lights and  
  controller to complete the buckets.  
   
INCLUDES: RTR Yeti SCORE Trophy Truck with Radio, ESC, Brushless Motor, Body,  
  Body Accessories, 32P 64P Spur Gear, 32P 16T Pinion Gear,  
  Instruction Manual  
   
REQUIRES: Battery: 2S or 3S LiPo pack with Dean's connector  
  Battery Charger: To match selected LiPo Battery  
  LiPo Charging Sack, Track and Maintenance Equipment
Buy this